1，GDRV是什么意思 電視機項目數據

2，64位win7頻繁藍屏看記錄都是gdrvsys引起什么情況 藍屏的種類有很多種，究其原因也十分復雜。不過想徹底解決藍屏我有小小心得。出現藍屏的原因往往集中在不兼容的硬件和驅動程序、有問題的軟件、病毒等。請按如下方法排除解決：1、硬盤連線是否松動；無異常后，對硬盤進行查錯處理；2、系統是否有病毒，建議安全模式下掃描殺毒； 3、把BIOS恢復出廠狀態試試；4、裝系統后硬件的驅動程序是否安裝成功？ 5、最好先重裝操作系統； 6、如重裝系統后仍有問題，則極可能是硬件不兼容所致； 7、向商家或周圍熟悉電腦的朋友咨詢一下也好，或許他們會給予幫助； 8、祝你好運！ 望能幫到朋友你！

3，TPS40210芯片BP腳的功能是什么接了一個電容對地電容壞了電壓就沒有了 網上很方便查，5 Pin Configuration and FunctionsDGQ10-PinTop ViewDRC10-PinTop ViewPin FunctionsPINI/ODESCRIPTIONNAMENO.BP 9 O Regulator output pin. Connect a 1.0 μF bypass capacitor from this pin to GND. 穩壓器輸出引腳。 在此引腳與GND之間連接一個1.0μF旁路電容。BP就是旁路（ByPass）的意思。一般是自舉電容之類的。由于芯片內部制造電容電感很困難（制造半導體器件如晶體管卻很容易），所以設計時把集成電路中需要接電容的地方用引腳引出來，在芯片外面接。所以越大的芯片引腳越多，四周放的電容也越多。COMP 4 O Error amplifier output. Connect control loop compensation network between COMP pin and FB pin. DIS/EN 3 I Disable pin. Pulling this pin high， places the part into a shutdown mode. Shutdown mode is characterized by a very low quiescent current. While in shutdown mode， the functionality of all blocks is disabled and the BP regulator is shut down. This pin has an internal 1 MΩ pull-down resistor to GND. Leaving this pin unconnected enables the device. FB 5 I Error amplifier inverting input. Connect a voltage divider from the output to this pin to set output voltage. Compensation network is connected between this pin and COMP. GDRV 8 O Connect the gate of the power N channel MOSFET to this pin. GND 6 - Device ground. ISNS 7 I Current sense pin. Connect an external current sensing resistor between this pin and GND. The voltage on this pin is used to provide current feedback in the control loop and detect an overcurrent condition. An overcurrent condition is declared when ISNS pin voltage exceeds the overcurrent threshold voltage， 150 mV typical. RC 1 I Switching frequency setting pin. Connect a resistor from RC pin to VDD of the IC power supply and a capacitor from RC to GND. SS 2 I Soft-start time programming pin. Connect capacitor from SS pin to GND to program converter soft-start time. This pin also functions as a timeout timer when the power supply is in an overcurrent condition. VDD 10 I System input voltage. Connect a local bypass capacitor from this pin to GND. Depending on the amount of required slope compensation， this pin can be connected to the converter output. See Application Informationsection for additional details.